![]() ![]() Step 2: Click on the “Start Test button” which will activate the full-screen mode. Step 1 (optional): Clean or rinse your screen with a soft fabric to wipe away dust if any. If you need a quick efficient defective screen pixel detector, all you need to follow the below-mentioned very easy rules to perform. Steps To Perform a Stuck OR Dead Pixel Test: 1.2 Color (Red, green, blue) Screen Defective Pixel Test.1.1 Difference Between stuck pixel or a dead pixel. ![]() 1 Steps To Perform a Stuck OR Dead Pixel Test:.Using these buttons with an incorrect Channel Mode selected will produce unintended results. Please remember that while the buttons may refer to 'Controller', Cosmic Color Bulbs or Pixels that are in Dual Normal mode will only update the string the Unit ID corresponds to. You can use the various buttons at the bottom of the Test Console to send lighting effect commands to the controller. However, if you check this box, the sliders will all be set to 0 when changing groups. When using the Select Pixel Group slider, the lights for the next selected group will be updated with the values of the current sliders. If your device supports more than 8 pixels, this selector is active and allows you to set which group of pixels to control. Due to screen space limitations, the Pixel Console can only show sliders for 8 pixels at one time. When working with DMX devices, this changes to allow selection of a DMX Universe.Ī Light-O-Rama RGB device can support up to 300 channels as 100 pixels, and DMX Universes can support up to 510 channels as 170 pixels. Always ensure the channel mode matches the device you are trying to test. For example, if you have a Cosmic Color device connected to your Enhanced LOR network, but have specified No Macro Channels (PixCon16) channel mode, results are going to be random once you pass channel 150. If you incorrectly set the channel mode, you may experience strange behavior on your device. Please note that the Pixel Console does not know exactly what device(s) you have connected to your Enhanced LOR network. The No Macro Channels option is only available if you have selected the LOR Enh (PixCon16) controller type. Set this to match the configuration of your Cosmic Color device or to No Macro Channels (PixCon16). This section (in the lower right) is available only if the controller type is set to "Cosmic Color Bulb/Pixel" or LOR Enhanced. If you license does not support Enhanced LOR networks, the LOR Enh. If your license does not support native DMX the DMX and LOR Enh. Use this section (in the lower left) to choose whether to use a test a Light-O-Rama CMB24 controller, Cosmic Color Ribbon, Cosmic Color Bulb/Pixel device, a DMX universe, or network device like the PixCon16 running on the REGular network in LOR Enhanced mode. The numbers shown in the box are the LOR intensities of each of the sliders, or the DMX Channel values in R/G/B order. Clicking this box will bring up a color selection dialog that will set the R G and B components automatically. You should always reference what is actually output on the physical device when selecting color values. NOTE: colors on your monitor may not exactly match what you would see on the actual device. The colored label box under each group of 3 sliders shows an approximate representation of the color that will be output by the device. The top number is the Pixel Number, the bottom three numbers are the Circuit or Channel IDs. The top portion of the pixel console shows up to twenty four sliders for the intensities of eight RGB pixels, plus a master slider (on the left) which can be used to slide them all simultaneously.Ībove each slider are the Physical Pixel Number and the Light-O-Rama circuit IDs, or DMX Channels associated with that triplet. The Pixel Test Console of the Hardware Utility This will require that you have the LOR Control Panel loaded.ģ.Only devices on the REGular network can be tested.Ĥ.The REGular network must be defined to be running at 500K in Enhanced mode.ĥ.You did not allow the Hardware Utility to take control of the REGular port from the Listener on start up. The Pixel Console can be used to test PixCon16 devices running in LOR mode as long as:ġ.Your software is registered and your license level supports Enhanced LOR Networks (Pro)Ģ.The Comm Listener is running. The Pixel Console can be used to test DMX and E1.31 RGB devices as long as:ġ.Your software is registered and your license level supports Native DMX Devices (Advanced or Higher)ģ.You have properly defined your DMX Universe in Network Preferences. The labels above each group of sliders show the physical pixel number, as well as the LOR channels in use. The Pixel Test Console is best used to test RGB Light-O-Rama controllers. Clicking on the "Pixel Console" button of the Light-O-Rama Hardware Utility opens the Pixel Test Console. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |